The G.O.R.E. Project: How to Stop Your Home from Losing Heat this Winter
This winter, an inexpensive, easy, and renter-friendly way to heat your home is to ensure it’s properly insulated so you’re not losing heat in the first place. To that end, your number one priority should be insulation.
This project comes from our handbook of green building projects, The Carbon-Free Home: 36 Remodeling Projects to Help Kick the Fossil-Fuel Habit by Stephen and Rebekah Hren. It’s full of DIY projects of varying levels of difficulty and cost. (This one is cheap and painless.)
Project Time: One weekend.
Energy Saved: High. Drafts can suck much of the heat out a home very quickly.
Ease of Use: N/A.
Maintenance Level: None.
Skill Levels: Carpentry: Basic.
Materials: Caulk, silicone.
Tools: Caulking gun, pry bar, screwdriver, incense or smoke stick.
Blow-in insulation. For older homes, the best way to seal up a drafty house is often by blowing insulation, either cellulose or fiberglass, into the walls and attic. Loose-fill insulation can reduce airflow to the point where air infiltration is essentially eliminated. If your home is poorly insulated, blowing in insulation in the attic and walls should be your top priority. It’s probably best to hire someone for at least the wall insulation. The reason to hire out is because blowing in sufficient insulation to get up to R-13 or so requires pressure created by a high-powered compressor that is not easy to rent. Walls and attic can be done in an afternoon by a professional. However, the attic doesn’t require high pressure and can be a DIY job if you’re so inclined. Many rental places or big-box stores have the equipment needed to blow in attic insulation.
Checking for air leaks. If your walls are already insulated, you’ll want to check all protrusions into the interior wall space for potential air leaks. This is easy to do with a stick of incense, when the interior temperature is substantially different than the exterior temperature. Hold a smoking stick close to things such as outlets, tops and bottoms of baseboards, chair rails, picture rails, window trim, plumbing intrusions, and vents, and watch the smoke. If it’s not floating straight up, you found one.
Outlets and switch seals are made of rubber and match the profile of the outlet (receptacle or switch). These can be purchased at most hardware stores. Remove the outlet cover with a screwdriver and stick the seal in between the cover and the wall. Be cautious of live wires; to play it safe turn off the breaker for the circuits you will be working on whenever removing outlet covers.
Drafts from gaps in trim or plumbing and HVAC intrusions can be sealed with either pure silicone (which is preferred as it stays flexible, but it is not paintable) or painter’s caulk with some silicone added. Expandable foam is an option for large cracks (more than a 1/4 inch), although it often contains potential toxins like benzene and often uses HCFCs for blowing agents, known to be potent greenhouse gases.
Stopping vertical airflow. If your home is old and your interior walls are extremely drafty, you have two options. The first is to seal either the basement or the attic. This will close either the entrance (basement) or the exit (attic) for the cold air. Again, blowing in insulation in the attic does a great job of essentially eliminating potential basement-to-attic airflow through interior walls. The cheapest (but most difficult) choice is to go into the basement or crawl space and clog any holes made in the floor and walls for systems such as electrical and plumbing. There are often a surprising number of these. This can be done with expanded foam or by stuffing bits of fiberglass insulation into the holes. While fiberglass insulation does let through some air, it reduces airflow by over 90 percent.
If your house is on piers and not enclosed, you’ll need to insulate your floor. This is an unpleasant and difficult task but will go a long way in sealing up your home. Flexible rods are sold to hold floor insulation in place, but we’ve seen these fail on a number of occasions. The best method for holding floor insulation in place is to start with a few of these flexible rods and then staple chicken wire to keep it in place.
Recessed lights and electrical boxes in the ceiling are a common escape route for air. Again, blowing some insulation in the attic will do wonders. Fiberglass batts in the attic also benefit from this treatment, as the gaps between the edges and the joists can let out a fair amount of heat.
Check all ductwork. If you have a conventional furnace or heat pump with forced-air heating, you’ll need to check your ductwork annually. This is because some piece or other has quite likely become detached over the course of time and is lying on the crawl space floor, keeping the crickets warm. To detect a detached duct, check each heating vent in your house, while the heating system is running, by placing your hand over the vent to feel for airflow. What you can’t check from above are slightly detached or leaky connections, which occur with great regularity. Grab the incense stick and check all the lines for leaks, using real duct tape (black, not gray, and quite expensive) to seal any problem areas. Also check for crimped ductwork or holes from squirrels or rodents. Repair any problem areas.
In a really well-sealed home, there’s the potential to have an inadequate amount of fresh air coming in from the outside. If you’ve done a great job sealing your home, and especially if you heat with wood (which uses up a lot of oxygen), you’ll want to install an air exchanger. This brings in fresh air and exhausts interior air through a highly conductive metal passageway that exchanges much of the heat of the outgoing air with the incoming air.
William Wordsworth was right when he said, “Nature never did betray the heart that loved her.” Nevertheless, the cold, dark days of winter can still get the best of even Nature’s most tenderhearted admirer. What’s one to do? We here at Chelsea Green have concocted the perfect cabin fever remedy with our suggested winter reading…Read More
Great news for French-speaking fans of Ben Falk’s The Resilient Farm and Homestead: An Innovative Permaculture and Whole Systems Design Approach. The French language translation is now available from Imagine Un Colibri, from French booksellers, and on Amazon.fr. Falk’s book is a technical manual that details the strategies he and his team have developed for…Read More
Are you prepared in the event of a sudden emergency? Blizzard, earthquake, insurrection after the inauguration? We know a lot of people are wondering what’s coming next in the US, as well as the world, given terrorism, politics, and global warming, among other threats. In this excerpt from When Technology Fails, a popular book on…Read More
Ah, 2016 – where did the time fly? It seems like only earlier this year we were excited about designing swales and getting to know more about no-till farming, and we ended up focusing on the heart, ketogenic diets and seeking a bio-abundant future. While the top 7 blog posts of the year don’t exactly…Read More
Uncertainty got you down? The political world may seem like it’s crumbling around us, but this we know: We can make it, America. Literally, we can make things. Houses. Gardens. Food. Below we’ve selected some of our classic how-to and DIY books (and some new favorites) to help you sustain your self, family, and community.…Read More